Universal Remote Control RNC-100 Guía para resolver problemas descargar pdf (Pagina 28)

ENGLISH

ENJOYING SURROUND SOUND

• Surround sound effect will not work properly if the signal passes through a graphic equalizer.

Please refer to your equalizer operating instructions for guidance on switching off (or defeating) the equalizer.

󳂮Note: Before surround playback, first perform the SPEAKER SETUP procedure, etc. on the OSD menu for optimum

performance. (For details, refer to “SETTING THE SPEAKER SETUP” on page 46.)

Depending on the input digital signal format, select the desired decoding mode.

• You can select the “DTS”, “DOLBY DIGITAL”, “PCM” or

“MPEG” mode directly on the remote control.

• Each time the DECODING MODE button is pressed, the

decoding mode changes as follows :

* Auto mode(“AUTO” lights up): The input digital signal format

(DTS, Dolby Digital, MPEG or PCM( 2 channel stereo), etc.)

used by the selected digital input source is detected

automatically to perform the necessary decoding process for

optimum surround mode.

* Dolby Digital mode(“DOLBY DIGITAL” lights up): The Dolby

Digital signal processing is performed only when Dolby Digital

signals are input.

* DTS mode(“ DTS” lights up): The DTS signal processing is

performed only when DTS signals are input.

* MPEG mode(“MPEG” lights up): The MPEG signal processing

is performed only when MPEG signals are input.

* PCM mode(“PCM” lights up): The PCM signal processing is

performed only when PCM signals are input.

AUD1

VID6 7.1IN

DTS PL2MV

DOLBY PL2MS

PCM NEO6C

MPEG NEO6M

PAGE1

DECODING

STANDBY

POWER ON

MAIN

PAGE

FAV

MUTE

CH.

SET

VOL

CH/

ADJUST

DSP

DECODE

DSP

DECODE

Select the desired surround mode.

• Each time the MULTI CONTROL knob is rotated or the DSP MODE

UP(▶) or DOWN(◀) button is pressed , the surround mode changes

depending on the input signal format and the selected decoding mode

as follows :

Signal format being input Selected decoding mode Selectable surround mode

Dolby Digital 5.1, Auto, Dolby Digital mode (DOLBY DIGITAL EX,)

Dolby Digital EX 6.1 channel sources DOLBY DIGITAL

Dolby Digital 2 channel sources (DOLBY DIGITAL EX,) DOLBY DIGITAL [,PL II MOVIE, PL

II MUSIC, PL II GAME]

DTS sources Auto, DTS mode (DTS ES MATRIX or DTS ES DISCRETE,) DTS

MPEG sources Auto, MPEG mode MPEG

PCM ( 2 channel ) sources Auto, PCM mode [PL II MOVIE, PL II MUSIC, PL II GAME,] BYPASS,

Analog stereo sources

DTS NEO 6 : CINEMA, DTS NEO 6 : MUSIC, THEATER,

MOVIE, HALL 1/2, STADIUM, CHURCH, CLUB 1/2,

ARENA 1/2, GAME, 4CH STEREO, MATRIX

( ): Possible only when surround back channel is not set to “None”, [ ] : Possible only when surround back channel is set to “None”.

(Refer to “When selecting the SPEAKER CONFIGURATION” on page 46.)

BYPASS mode: Audio signals bypass signal processing circuits for surround sound and are palyed in stereo mode.

• You can select the “PL II MOVIE”, “PL II MUSIC”, “DTS NEO: 6 CINEMA” or “DTS NEO : 6 MUSIC” mode directly on the

remote control depending on the input signal format and the selected decoding mode.

• When MPEG signals are input in the required decoding mode, the corresponding surround mode will be automatically selected

regardless of using the MULTI CONTROL knob or DSP MODE UP(▶) or DOWN(◀) button.

■Notes:

• When the selected decoding mode is not matched to the input signal format, the indicator of the signal being input flickers, meaning

the required process cannot be performed and no sound is heard. Therefore, be sure to select the required decoding mode and the

available surround mode according to the input signal format.

• When the 8 CH DIRECT is selected as an input source, the decoding and surround modes cannot be selected.

• When the pure audio function is activated, the surround mode cannot be selected.

• When 96 kHz PCM signals are input , the stereo mode is automatically selected.

■Notes :

• Only when the digital input is selected as signal input for the

input sources except PHONO, TUNER and TAPE

MONITOR, the decoding mode can be selected.

• Noise may be generated at the beginning of playback and

while searching during DTS playback in the auto mode. In this

case, try playing in the DTS mode.

AUD1

VID6 7.1IN

DTS PL2MV

DOLBY PL2MS

PCM NEO6C

MPEG NEO6M

PAGE1

STANDBY

POWER ON

MAIN

PAGE

FAV

MUTE

CH.

SET

VOL

CH/

ADJUST

DSP

DECODE

DSP

DSP DSP

MULTI CONTROL

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 66 67

Comentarios a estos manuales

Sin comentarios

Universal Remote Control RNC-100 Guía para resolver problemas Pagina 28

Comentarios a estos manuales

Relacionado con productos y manuales para Receptores AV Universal Remote Control RNC-100