Universal Remote Control RNC-100 Guía para resolver problemas descargar pdf (Pagina 22)

ENGLISH

ENJOYING SURROUND SOUND

Depending on the input digital signal format, select the desired decoding mode.

• Each time the AUTO button is pressed, the decoding

mode changes as follows :

󰥪

IN-AUTO : The input digital signal format(DTS, Dolby

󰥪 Digital or PCM(2 channel stereo), etc.) used by the

selected digital input source is detected

automatically to perform the necessary decoding

process for optimum surround mode.

IN-DTS : The DTS signal processing is performed only

󰥪 when DTS signals are input.

IN-PCM : The PCM signal processing is performed only

when PCM signals are input.

AUTO

12345

67890

T.TONE

DSP

STEREO

POWER

AUDIO

VCR

SPK SET

ADJUST

M1 M2 M3

AUDIO SEL.

OSD

SETUP

SLEEP

DISPLAY

DIMMER

RETURN

P.SCAN

TUNER C D AUX

VIDEO1 VIDEO2 VIDEO3

TAPE

7CH DIR.

TUNE

PRESET

ENTER

SUBTITLE ZOOM

VOLUME

MUTE

CH SEL. CH/LEVEL

MACRO

DVD CABLE SAT

CD AUX TV

STANDBY

PARA.

UNIVERSAL REMOTE CONTROL

RNC

AUTO

Select the desired surround mode.

• Each time the DSP MODE ◀or ▶ button is pressed, the surround mode changes depending on the input signal format

and the selected decoding mode as follows :

※When Dolby Digital signals are input in the IN-AUTO mode, one of the following modes can be selected depending

on the number of the recorded channels.

• Dolby Digital 5.1 or Dolby Digital EX 6.1 channel sources :

(DOLBY DIGITAL EX,) DOLBY DIGITAL and DOLBY VIRTUAL

• Dolby Digital 2-channel sources :

(DOLBY DIGITAL EX,) DOLBY PRO LOGIC II CINEMA, DOLBY PRO LOGIC II MUSIC, DOLBY PRO LOGIC and

DOLBY VIRTUAL

( ): possible only when surround back speaker setting is not “N”.

※When PCM(2 channel stereo) signals are input in the IN-AUTO or IN-PCM mode, one of the following modes can be

selected.

• DOLBY PRO LOGIC II CINEMA, DOLBY PRO LOGIC II MUSIC, DOLBY PRO LOGIC, DOLBY VIRTUAL, DTS

NEO 6 CINEMA, DTS NEO 6 MUSIC, THEATER, HALL and MATRIX

• When the analog input is selected as signal input and analog stereo signals are input, you can select the desired of

these above surround modes, too.

• However, when DTS signals are input in the IN-AUTO or IN-DTS mode, the corresponding DTS mode will be selected

regardless of using the DSP MODE ◀ or ▶ button.

■Notes:

• When the selected decoding mode is not matched to the input signal format, the “DIGITAL” indicator flickers and

no sound is heard. Therefore, be sure to select the required decoding mode and the available surround mode

according to the input signal format.

• When the 7 CH DIRECT is selected as an input source, the decoding and surround modes cannot be selected.

• When the digital signals are not inputted, the desired surround mode cannot be selected.

■Notes :

• Only when the digital input is selected as signal input for the input sources except TUNER, TAPE and AUX, the

decoding mode can be selected.

• Noise may be generated at the beginning of playback and while searching during DTS playback in the IN-AUTO

mode. In this case, try playing in the IN-DTS mode.

AUTO

12345

67890

T.TONE

DSP

STEREO

POWER

AUDIO

VCR

SPK SET

ADJUST

M1 M2 M3

AUDIO SEL.

OSD

SETUP

SLEEP

DISPLAY

DIMMER

RETURN

P.SCAN

TUNER C D AUX

VIDEO1 VIDEO2 VIDEO3

TAPE

7CH DIR.

TUNE

PRESET

ENTER

SUBTITLE ZOOM

VOLUME

MUTE

CH SEL. CH/LEVEL

MACRO

DVD CABLE SAT

CD AUX TV

STANDBY

PARA.

UNIVERSAL REMOTE CONTROL

RNC

DSP

DSP MODE

RD-8108R 2002.11.7 3:35 PM 페이지23

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 43 44

Comentarios a estos manuales

Sin comentarios

Universal Remote Control RNC-100 Guía para resolver problemas Pagina 22

Comentarios a estos manuales