Universal Remote Control ONE FOR ALL URC3220 Manual de usuario descargar pdf (Pagina 5)

INSTALLING BATTERIES

1. On the remote control’s back, push the tab and lift off the

battery cover.

2. Obtain two (2) new AAA alkaline batteries.Match the +

and – marks on the batteries to the + and – marks in the

battery case, then insert the new batteries.

3. Press the battery cover back into place. The tab should

click when the cover is locked.

4. Test the remote control by pressing any mode key (e.g.,

TV). If the batteries are inserted correctly, the LED (red

light) will blink.

NNOOTTEE:: WWhheenn bbaatttteerriieess nneeeedd rreeppllaacceemmeenntt,, tthhee rreemmoottee ccoonnttrrooll wwiillll ssttoopp ooppeerraatt--

iinngg..RReemmoovvee tthhee oolldd bbaatttteerri

ieess aanndd iinnsseerrtt nneeww oonneess wwiitthhiinn 1100 mmiinnuutteess ttoo

eennssuurree aallll ooff yyoouurr pprrooggrraammmmiinngg iinnffoorrmmaattiioonn iiss rreessttoorreedd..

PROGRAMMING DEVICE CONTROL

The One For All 3 Device Universal Remote Control is preprogrammed at

the factory to operate an RCA TV, a Toshiba DVD player,and a Motorola

cable box.To control devices other than the default brands,perform the fol-

lowing steps; otherwise skip this section:

1. Turn on a desired device (e.g.,VCR or DVD player) and, if

applicable, insert media (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely before proceeding.

Highlight or write down the codes and device you wish to program

before starting step 2.

2. On the remote control,press a device key once (i.e.,DVD/VCR,

CBL/SAT,or TV).

NOTE: To program control of a VCR, PVR (or DVR), TV/VCR Combo,

or TV/VCR/DVD Player Combo press DVD/VCR once. After program-

ming a VCR Combo device, you will be able to control channel selec-

tion, volume, and VCR functions.

NOTE: To program control of a DVD Player, DVD Player/VCR

Combo, or TV/DVD Player Combo, press DVD/VCR once. After pro-

gramming a DVD Combo device, you will be able to control channel

selection, volume, and DVD functions.

NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR)

Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)

Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,

then release

SET.

4. Use the

Manufacturer’s Codes

(starting on page 34) to

locate the type of device and brand name and then enter

the first four-digit code for your device.If performed cor-

rectly, the

LED will blink twice.

NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter

the same code again.

5. Aim the remote control at the device and press POWER

once. The device should turn off. If it does not, repeat

steps 2 through 5, trying each code for your brand until

you find one that works.If it still doesn’t work,try

Searching For Your Code on next page

NOTE: If the device does not have a POWER key, press PLAY.

6. Repeat steps 1 through 5 for each device you want to con-

trol.For future reference,write down each working device

code in the following boxes:

DVD/VCR Code:

Device Type:__________________

CBL/SAT Code:

Device Type:__________________

TV Code:

Device Type:__________________

WALRB3P manual booklet 5/2/06 3:13 PM Page 7

1 2 3 4 5 6 7 8 9

Comentarios a estos manuales

Sin comentarios

Universal Remote Control ONE FOR ALL URC3220 Manual de usuario Pagina 5

Comentarios a estos manuales