Universal Remote Control 10IN1 Manual de instrucciones descargar pdf (Pagina 9)

After Sales Support

Telephone: 1300 663 907

Internet: www.winplus.com.au

After Sales Support

Telephone: 1300 663 907

Internet: www.winplus.com.au

19 8

Programming the

Remote Control

Programming Device Codes

To program this remote to function with your Bauhn,

Tevion or Vivid brand device, please refer to the learning

function on page 13 of this product manual.

To be able to control a device with your universal remote

control, you must ﬁrst set up the corresponding device

codes. For the PC device selection, please see “Controlling a

PC” under the special features section

There are different ways to setup the device codes

• Search for your device by manufacturer

• Use the code book to program the remote control

• Use automatic search to locate the suitable device code

This type of programming is recommended if your device

is not contained in the list of preset codes

• The learning function can be used to learn the functions

and features of any IR remote

Programming the Device Code by

Manufacturer Name

Switch on the device you want to program the remote control

to. If your device is a VCR or a CD or DVD player, please

insert a tape or CD/DVD.

To cancel the following programming at any time, press

EXIT (23) to return without saving any changes. Press the

EXIT button (23) multiple times until the remote control

has returned to standard mode.

Proceed as follows to program the device codes (this

example refers to programming a TV set).

1. Point the remote control to the TV set while entering the

commands.

2. Press the source device selection button of the device

you want to program. In this example, it is the TV button

(2). The display shows [TV].

3. Press and hold the SET button (21) for at least 3 seconds.

The display shows [CODE SETUP]. Then release the SET

button (21).

4. Press the OK button (22). The display shows [BRAND

SRCH].

5. Press the OK button (22). The display shows the

ﬁrst preset manufacturer name, e.g. [A R SYSTEM].

Underneath the device code of the displayed

manufacturer appears.

Consistent Volume Control

The (VPT–Volume Punch Through) volume control guarantees

that the volume control is always made for the TV set or Hiﬁ

equipment regardless of the sound source that you have

selected. Therefore, you will not have to press the TV or

AUDIO source buttons before you set the volume with the

VOL+ (10), VOL- (11) or MUTE (7) buttons.

Example:

The remote control is programmed for your TV

set and your DVD player. You play a DVD and the

remote control is set to the DVD (2) source. This

allows you to control the DVD playback using the

remote control. But you can control the TV set

volume without having to press the TV source

selection button ﬁrst.

NB: The PC mode does not support consistent

volume control.

Switching VPT between TV and AUDIO

VPT is set to TV as default. For any source that you select,

the volume control will always control the TV set. But if

you’re using a home cinema and you output the sound via

Hiﬁ equipment, you can switch the volume control to the

Hiﬁ equipment.

Proceed as follows:

1. Press the AUDIO source selection button (2).

2. Press and hold the SET button (21) for at least 3 seconds.

The display shows [CODE SETUP]. Then release the SET

button (21).

3. Press (8) twice. The display shows [BASIC VPT].

4. Press the OK button (22). The message [SUCCESS]

will appear for a few seconds on the display.

5. Quit the process by pressing the EXIT button (23).

VPT is now set to the device that is controlled via the AUDIO

source selection button.

If you want to use the TV for sound output again,

repeat the above steps by using the TV source

selection button (2) in the ﬁrst step.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Comentarios a estos manuales

Sin comentarios

Universal Remote Control 10IN1 Manual de instrucciones Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para Controles remotos Universal Remote Control 10IN1