Universal Remote Control URC-L-1870 Manual de usuario descargar pdf (Pagina 2)

Congratulations! Your Universal Remote Control (URC) is a state-of-the-art

device which integrates many different infra-red remote controls to deliver

instant A/V action to your fingertips.

Before operating the remote, please read thoroughly (1) the interior of the

coversheet and (2) this manual. Then reserve them for future reference.

1 HOW TO INSTALL BATTERIES

Alkaline batteries are recommended. The number of battery required stated

at the back of the coversheet.

1. Remove the battery cover on the back of your URC.

2. Observe the polarity of the batteries and the “+/–” marks inside the battery

compartment.

3. Insert the batteries.

4. Push the battery cover back in place.

Battery Low

If the indicator flashes twice slowly after your invoking of any command, it

shows that the battery level is low. You must replace them with new batteries

to ensure proper functioning.

2 HOW TO SET UP THE URC

By entering Device Code

You may setup the URC by the following code entering instructions.

1. Refer to the DEVICE CODE LIST, look up the 4-digit Device Code which

corresponds to the brands of your A/V equipment. If there are more than

one Device Code listed under your brand, try from the first code.

2. Press a desired Device Mode Key (e.g. ).

3. Hold down “ CH+ ” and “ VOL– ”on the URC together simultaneously for 2

seconds until the indicator lights up.

4. Use the number keys to enter your 4-digit Device Code, the indi-

cator should go out immediately.

Turn on your device (e.g. TV), try the function keys on the URC. If your device

(e.g. TV) responds to your invoked function correctly, you have entered the

right Device Code. Otherwise, repeat the above setup instructions with the

rest available Device Codes until your device (e.g. TV) responds to your in-

voked function, and most keys work correctly.

* Simply repeat the above procedures to enter the Device Codes for your

DVD. (Remember to press a correct Device Mode Key in step 2 above.)

English

Note :

– If the indicator flashes twice in step 4, a wrong Device Code has been

entered. You are required to repeat step 2 to 4 again.

Suggestion :

– If you cannot find a correct Device Code for your equipment, see 2 HOW

TO SET UP THE URC– By Searching Through the Library.

– You are recommended to jot down your Device Codes in the space provided

on back label after setting up the URC correctly for future reference.

English

By Searching Through the Library

If you cannot identify a correct Device Code for your equipment from the Device

Code list, you may search the code through the library:-

1. Turn on your device manually (e.g. TV).

2. Press a desired Device Mode Key (e.g. ).

3. Hold down “ CH+ ” and “ VOL– ” on the URC together simultaneously for 2

seconds until the indicator lights up.

4. Enter a corresponding Magic Search Code from following table. The in-

dicator should go out immediately.

DEVICE TYPE: TV DVD

MAGIC SEARCH CODE:

0001 0005

(e.g. press device mode key, then press “ CH+ ” and “ VOL– ” , and enter

TV Magic Search Code 0001.)

5. Press the same desired device mode key again as in step 2 above. (e.g. )

6. Hold down “ CH+ ” & “ VOL– ” together simultaneously for 2 seconds until

the indicator lights up, and your URC is ready to start searching.

7. Aim the URC at your device (e.g. TV), press the “ ” key repeatedly, slowly

and patiently until the device has been turned off.

Once your device has been turned off, immediately press “ CH+ ” and

“ VOL– ” to lock in code and the indicator should go out.

* Simply repeat the above setup procedures to search the Device Code for

your DVD. (Remember to press a correct Device Mode Key and correct Magic

Search Code in step 2-5 above)

IMPORTANT:

– If the power on/off function of your device is not infra-red controlled - you

need to follow steps 2 to 6 above and start searching :-

• Press “ ” and another important function key alternately until your

device responds to the expected function, press “ CH+ ” and “ VOL– ” to

lock in the code.

e.g. Press “ ” & “ 1 ” alternately, or ;

Press “ ” & “ ” alternately.

Note:

– Each time you press the “ ”, the URC will skip to the next code and

send out a POWER signal trying to turn off your device.

If you failed to stop pressing “ ” in time when your device has been

turned off, turn on your device again immediately. Before the indicator

goes out, press “ ” on the URC to skip backward. Repeat the step 7

above and lock in code.

– If the indicator flashes twice after your pressing of “ ” key, you are

already at the last code of the library. Press “ CH+ ” and “ VOL– ” to resume

the URC and repeat carefully the above procedures to search again.

3 OPERATING THE URC

Normal Operation

Once you have set up the URC for your A/V equipment, it works like your origi-

nal remote controls. To operate, just aim it at your equipment, press an appro-

priate device mode key and invoke the desired function by pressing a corre-

sponding key on the URC. The indicator flashes during signal transmission and

as confirmation of key touch.

1 2 3 4 5 6 7 ... 12 13

Comentarios a estos manuales

Sin comentarios

Universal Remote Control URC-L-1870 Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Controles remotos Universal Remote Control URC-L-1870