Universal Remote Control R7 - SPECS SHEET Manual de usuario descargar pdf (Pagina 13)

Data Sheet ADP5585

Rev. C | Page 13 of 40

GPI EVENT

Y EVENT

LOGIC EVENT

(R1) LA

LA_INV

CLR

SET

LB_INV

LC_INV

FF_SET

FF_CLR

R3_EXTEND_CFG[1:0]

LOGIC_SEL[2:0]

LY_INV

(R2)

(R3)

LOGIC BLOCK

(R0)

LOGIC_INT

LOGIC_INT_LEVEL

LOGIC_EVENT_EN

OVRFLOW_INT

EVENT_INT

RESET_TRIG_TIME[2:0]

RESET1_EVENT_A[7:0]

RESET1_EVENT_B[7:0]

RESET1_EVENT_C[7:0]

RESET2_EVENT_A[7:0]

RESET2_EVENT_B[7:0]

FIFO

EC[4:0]

09841-017

LOGIC

EVENT/INT

GENERATOR

C BUSY

FIFO

UPDATE

Figure 18. Logic Block Overview

PWM BLOCK

The ADP5585 features a PWM generator whose output can be

configured to drive out on the R3 I/O pin. PWM on/off times

are programmed via four 8-bit registers (see Figure 20). Each

bit of the on or off time represents 1 µs. The highest frequency

obtainable from the PWM is performed by setting the least

significant bit of both the on and off time bit patterns, resulting

in a 500 kHz signal with a 50% duty cycle.

The PWM block provides support for continuous PWM mode

as well as a one-shot mode (see Table 59). Additionally, an

external signal can be AND’ed with the internal PWM signal.

This option can be selected by writing a 1 to PWM_IN_AND

(PWM_CFG[2]). The input to the external AND is the C3 I/O

pin. C3 should be set to GPI. Note that the debounce for C3

results in a delay of the AND’ing, and can be turned on or off

using Register 0x21.

Newly programmed values are not latched until the final byte,

PWM_ONT_HIGH_BYTE (Register 0x32, Bits[7:0]), is written.

09841-018

LA_INV

MUX

000

001

SEL[2:0]

OUT

010

100

101

110

111

OUT

GND

AND

XOR

IN_L

IN_LB

IN_LC

IN_LA

SEL

OUT

AND

IN_LA

IN_LB

IN_LC

R3_EXTEND_CFG[1:0] = 01

LOGIC_SEL[2:0]

LY_INV

SEL

OUT

LB_INV

OUT

IN_LB

LC_INV

SEL

OUT

IN_LC

FF_SET

FF_CLR

SEL

OUT

IN_LA

IN_LB

IN_LC

AND

OUT

XOR

IN_L

IN_LB

IN_LC

IN_L

IN_LB

IN_LC

XOR

CLR

SET

SEL

OUT

Figure 19. Logic Block

(C3) PWM_IN

OFF TIME[15:0]

PWM_EN

PWM_IN_AND

PWM_OFFT_LOW_BYTE[7:0]

PWM_MODE

PWM_OFFT_HIGH_BYTE[7:0]

PWM_ONT_LOW_BYTE[7:0]

PWM_ONT_HIGH_BYTE[7:0]

ON TIME[15:0]

SEL

OUT

09841-019

AND

PWM

GENERATOR

(R3)

PWM_OUT

Figure 20. PWM Block Diagram

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 39 40

Comentarios a estos manuales

Sin comentarios

Universal Remote Control R7 - SPECS SHEET Manual de usuario Pagina 13

Comentarios a estos manuales

Relacionado con productos y manuales para Controles remotos Universal Remote Control R7 - SPECS SHEET